P40 Agricultural Drone
35Pages

Dear user, thank you for choosing XAG products. For safety purposes and better user experience, it is highly recommended that you read this manual carefully and strictly follow the instructions hereof. If you have any questions about this document, please contact our Technical Support team via email: info@xa.com

Safety Guidelines • Please make sure that the drone operator has passed the drone operation training programme and obtained a drone pilot certificate prescribed by laws and regulations where the product is used in advance. Never operate the drone without permission unless otherwise provided. • bserve the surroundings, ensure a safe distance from the obstacles and the crowd as well O as eliminate unsafe conditions including environmental factors like bad weather and extreme temperatures before operation. • NEVER operate while drowsy, drunk or in a poor mental state so as to prevent...

Please check that the following items are all present when unpacking the box. Should there be any item missed, please contact your dealer. Tool Kit ×1 [1]：ACS2G ControlStick namely ACS2G Remote Control. 2

About P40 Agricultural Drone The main components of P40 Agricultural Drone are as follows: (Above) Figure 1: Airframe Module Structure 1 (Below) Figure 2: Airframe Module Structure 2

(Below) Figure 3: Airframe Module Structure 3 ㉓ Central Cabin Cover ⑥ SC (Electronic Speed E Controller) ⑦ Dynamic Radar ⑧ Terrain Sensor ⑨ Spraying Hub Housing ⑩ Searchlight ㉒ Flight Status Indicator ㉔ uper X4 Intelligent S Control System ⑯ Spraying Status Indicator ⑲ Liquid Tank Sensor Patch ⑳ Airframe Nameplate There are labels on the upper plate of the airframe and the aluminium sleeves of arms. The numbers 2 for 3 for 4 for 。

Airframe Assembly Preparation Remove Spraying Hub Housing Remove Spraying Hub Housing by unscrewing its 6 screws (2 on the top and 2 on both left side and right side ) Remove Central Cabin Cover and Arm Bracket Pull off the Liquid Tank Sensor Cable on the Spraying Hub. Liquid Tank Sensor Cable

Remove 8 Arm Brackets and Central Cabin Cover.

Arms Assembly Put the wire into the Arm. By matching the Arm Position Number to the Airframe Position Number, insert the Arm into the Airframe and fit the Arm Bracket.

Cable Connection Connect ESC Power Cables Upon Arms assembly, push the ESC Power Cables of Arm No.1 & No.2 into the hole of the Bottom Central Compartment and connect to those of arm No.3 & No.4. (The red connector fits only to the other red connector while the black one connects to the other black one). Arm No.2 ESC Power Cable Arm No.3 ESC Power Cable Arm No.1 ESC Power Cable Arm No.4 ESC Power Cable Lock ESC Power Cables of Arm No.3 & No.4 with Fastener. P lease remove the Fastener preceding connection of ESC Power Cables of Arm No.1 & No.2 and lock the Fastener back upon connection lest...

Tighten connectors on both sides with cable ties upon the connection between Power Cables of Arm No.1 & No.2 in the Bottom Central Compartment. (The red connector fits only to the other red connector while the black one connect to the other black one) Connect Signal Cable of Flight Indicator and Sprayer Pull the Flight Indicator Signal Cables of Arm No.1 and Arm No.2, plus those of the lights and sprayers of Arm No.3 and Arm No.4 through the hole on the Spraying Hub to the Bottom Central Compartment.

Connect Male and Female Connectors of Flight Indicator Before connecting the Flight Indicator Signal Cables, match the Female Connector of Arm No.1 to the Male Connector of Arm No.4 and match the Female Connector of Arm No.2 to the Female Connector of Arm No.3. Flight Indicator Male Connector Flight Indicator Plug Sprayer Plug Arm No.1 & No.2 Flight Indicator Cable Arm No.3 & No.4 Flight Indicator & Sprayer Cable Flight Indicator Female Connector Connect Cable of Flight Indicator and Sprayer Upon connection of Flight Indicator Signal Cables between Arm No.1 & No.4 and Arm No.2 & No.3,...

Connect ESC Signal Cable Connect ESC Signal Cable inside the Arm to ESC hub. NEVER swap the ESC Signal Cables between M1 and M2, M3 and M4, as incorrect connection may cause flight accidents Connect Liquid tube Pull the Liquid Tube inside Arm No.3 & No.4 through the hole as shown below and connect it to the Peristaltic Pump.

Reassembly of Removed Parts Fit the Spraying Hub Housing and Central Cabin Cover. When fitting the Central Cabin Cover, put the Liquid Tank Sensor Cable correctly and connect it to the Spraying Hub. (Please refer to Page 4 for the exact place). Liquid Tank Sensor Cable

Unfold Propeller After unfolding all the propellers, check whether the model of propeller, which could be seen between clamp and blade, corresponds to the Arm Number. CW Propellers correspond to Arm No.1 & No. 3, while CCW Propellers correspond to Arm No.2 & No.4. NEVER swap the CW and CCW Propellers, as incorrect installation may cause flight accidents.

RealTerra Installation Insert the RealTerra into the RealTerra Slot until hearing a clicking sound.

Smart Battery Preparation About Indicator / Button There are 1 power button and 6 indicators on the smart battery screen. Solid: Normal Slow Flash: Overcooled Fast Flash: Overheated Double Flash: Error Battery Level Indicator Battery Status Indicator Power Button Switch On/Off Battery Long-press twice to switch on/off the battery. After connecting the drone or the charger, long-press the battery button for at least 1 second until all the battery level indicators flash synchronously. Then long-press for another second until the battery beeps and the status indicator is ON/OFF, which means...

Charge with Intelligent SuperCharger Check Battery Level When the battery is OFF, short-press the power button once to check the battery level. When the battery is ON, the battery level indicators will be on solid. Check Battery Status When the battery is on, check the battery status on the screen. LED Behaviour 2 Lights Double Flash Fault Lock 3 Lights Double Flashing Remote Lock 4 Lights Double Flashing Anti-dismantling Lock 2/4 Alternate Flashing Lights Dual-battery Power on Disabled 2/3 Alternate Flashing Lights Over current Protection Battery locked for the low battery,please contact...