TX39H
1 / 67Páginas

OPERATOR’S MANUAL

WARRANTY CONDITIONS Warranty Coverage : TYM Tractor Division, herein referred to as TYM, undertakes to replace or repair any part of a TYM loader where damage has been proven to be caused by defects in material or workmanship. This Warranty is valid for a period of 1 year from the date of the original retail sale. Parts replaced or repaired under the terms of this Warranty are guaranteed only until the original warranty expires. Warranty only applies to the original purchaser. It is further understood and agreed that the defect should be immediately reported to the Selling Dealer. The...

Temporary repairs or additional costs due to the work being performed after normal working hours will not be compensated. The above warranty is in lieu of all other warranties on TYM's behalf and neither party assumes any other liability in connection with TYM's Products. Right To Make Design and Product Changes : TYM reserves the right to make changes in the design and other changes in its TYM Products at any time without incurring any obligation with respect to any product previously ordered, sold or shipped.

TABLE OF CONTENTS SAFETY –1 --------------------------------------------------------------- 5 SAFETY -2 ---------------------------------------------------------------- 6 SAFETY DECALS ------------------------------------------------------- 7 LOADER SPECIFICATION -------------------------------------------- 8 INTRODUCTION -------------------------------------------------------- 10 TRACTOR PREPARATION -------------------------- ----------------- 19 LOADER OPERATION -------------------------- ---------------------- 21 LOADER REMOVAL --------------------------------------------------- 26...

SAFETY Understand that your safety and the safety of other persons is measured by how you service and operate this loader. Know the position and operations of all controls before you to operate. Make sure you check all controls in all safe area before starting. The safety information given in this manual does not replace any safety Codes, insurance needs, federal, state and local laws. Make sure your Machine has the correct equipment required by your local laws and regulations. Read this manual completely and thoroughly and make sure you understand all controls. All equipment has a limit....

-Contact with overhead power lines can cause severe electrical burn or death from electrocution. Make sure there is enough clearance between raised equipment and overhead power lines. -Add recommended rear tire liquid weight or rear wheel weights for increased stability. -A loader attachment should be transported in a low position at slow ground speeds. -Make turns slowly and use the tractor brakes cautiously. -A loaded attachment in the raised position alters the center of gravity location of the machine and increases the possibility of mishaps. -Do not stand, walk or work under a raised...

Crushing Hazard Stay away from under lift arms and bucket! 1. Do not stand or work under a raised loader. 2. Support bucket and lift arms before working under the loader. 3. Lower the loader to the ground before leaving seat. 65*0-500-004-1 A WARNING NEVER TAKE USE OF FRONT END LOADER WITH TOWING OPERATIONS. ADANGER INTALL SAFETY PROP BEFORE WORKING UNDER RAISED STRUCTURE A WARNING 1. Add recommend®! rear vtfiee ball33l and /or rear counter-weight for slablity. 2. Move wtieefs to the widest recommended setting (or increasing stability. 3. Move and turn tractor at tow soaeds. 4. In...

INTRODUCTION The purpose of this manual is to assist you in maintaining and operating your loader. Read it carefully, it furnishes information and instructions that will help you achieve years of dependable performance. Some information may be general in nature due to unknown and varying conditions. However, through experience and these instructions, you should be able to develop operating procedures suitable to your particular situation. “Right” and “Left” as used throughout this manual are determined by facing the direction the machine will travel when in use. The photos, illustrations...

FILLING THE BUCKET Approach and enter the pile with a level bucket.Ease lever back and toward you to lift and rollback the bucket. The lift and rollback of the bucket will increase efficiency because a level bucket throughout the lifting cycle resists bucket lift and increases breakaway effort. Note: Do not be concerned if the bucket is not completely filled during each pass Maximum productivity is determined by the amount of material loaded in a given period of time.Time is lost if two or more attempts are made to fill the bucket on each pass

LIFTING THE LOADER WARNING Do not lift or carry anyone in the bucket or on any other position of the loader or loader attachment. Inadvertent movement of the loader or attachment could result in serious Injury or Death from falling or crushing. A CAUTION Make sure material in bucket cannot rollout and down on tractor when bucket is raised to full height .Keep clear of overhead obstructions such as trees, limbs or power lines when raising the bucket. When lifting the load, Keep the bucket positioned to avoid spillage. NEVER use the Front end loader with TOWING IMPORTANT: To prevent damage to...

CARRYING THE LOAD Position the bucket just below the level of the tractor hood for maximum stability and visibility, whether the bucket is loaded or empty. When transporting the load, Keep the bucket as low as possible to avoid tipping, in case a wheel drops in a rut. You need to drive at a reduced speed, e.g 10 km/h max , with a loaded attachment Use extreme caution when operating the loader on a slope, Keep the bucket as low as possible ,this keeps the bucket and tractor center of gravity low and will provide maximum tractor stability. DUMPING THE BUCKET Lift the bucket high enough to...

LOWERING THE BUCKET After the bucket is dumped,back away from the vehicle while lowering and rolling back the bucket The float will also prevent the mixing of surface material with stockpile material.The float position will reduce the chance of surface gouging when removing snow or other material. LOADING FROM A BANK OPERATING WITH FLOAT CONTROL During hard surface operation,Keep the bucket level and put the lift control in the float position to permit the bucket to float on the working surface.If hydraulic down pressure is exerted on the bucket,It will wear faster than normal. Exercise...